Inspired by Pinterest
I've been collecting photos on Pinterest featuring wreaths
and other door decorations for Christmas. Of all the ones I pinned, I most loved
those featuring a vintage skate as the container for a winter "floral"
arrangement. I pinned several and my Skater's Waltz combined ideas from
several. I found a pair of skates in an antique mall in the summer, snatched them up, and tucked them away for Christmas crafting. I'm thinking about placing a green wreath behind it as a backdrop—but
maybe I'll do that next year. Time is running out! I was surprised at how
little time it took to complete not one, but two—one to give as gift.
Directions below are for one skate. Have fun—there's still time to make one and
enjoy it for the months of December and January!
Materials for One Skate
- 1 vintage ice skate
- 2-1/2 yards 3/8"-wide patterned Christmas ribbon for
the "shoestrings"
- Assorted floral or novelty sprays—you will need several so
buy more than you think you will need; I used a spray of poinsettia, a large
spray of greens and a smaller one, plus pieces from a second spray of
poinsettia
- Narrow ribbon for the hidden hanger
Other Supplies and Tools
- Tissue paper
- Florist ties or green "twist ties"
- Craft glue
- Seam sealant such as Fray Check (not shown in photo below)
- Scissors with sharp points; also an awl if you have one
- Wire snips
- Tapestry needle or other needle with a large eye
- A piece of Styrofoam or heavy cardboard to hold the skates
upright while you work is helpful, but I didn't have a piece and managed
without.
Assembly
1. Cut the narrow ribbon for the ties into four even
lengths. To create points that will be easier to insert through the eyelets,
apply craft glue to the ends and roll to a point. Allow to dry.
2. Remove the original shoestrings and stuff the toe of each
skate with tissue paper.
3. When the ribbon points are dry, lace the skates until you
reach the eyelets. Add more tissue paper to fill in the heel area partially.
4. Arrange floral stems as you like them and test them in the
skate. They will probably be too long and you will need to cut away the excess
with wire cutters (or an old pair of scissors). You can also bend pieces of the
spray to create a pleasing and balanced look. This step is very experimental.
Play with stem placement until you are happy with it and how it looks in the
skate.
5. Use a green twist tie to hold the pieces in place. Don't
just wrap the tie around and around; weave it in and around the stems to secure
it in the desired position. Tie off.
6. Tuck the floral arrangement into the skate, along with
additional tissue paper to hold it in place. You will secure the spray to the skate in
step 9.
7. Support the skate in your lap or in a piece of Styrofoam
or heavy cardboard and complete the lacing, adding more tissue paper if needed.
Tie in a bow. Treat the cut ends with seam sealant, saturating about 1/2" of
each end. Allow to dry thoroughly. When the ribbon ends are dry, cut the ends at an angle,
through the "sealed" area.
8. To attach a ribbon hanger, use the points of a sharp
scissors (or an awl if you have one) to make a hole in the back of the skate at
about the center.
9. Cut an 18" length of the narrow red ribbon and use
the tapestry needle to thread it though the hole. Wrap one end around the
floral stems to secure it and tie a square knot, snugging it to the skate. Depending on the position of the twist tie, you might be able to pull the ribbon through it too--experiment!
10. Decide how long
you want the hanger and hold both ends of the ribbon together. Tie an overhand
knot. Cut the ribbon ends at an angle and treat with seam sealant (Fray Check). You can use a bit of craft glue on the knot and around the hole here if you like. I did because my spray wanted to stray from its desired location in the skate.
11. You may decide at this time to add more floral items in
the area below the floral spray to fill in and cover the upper edge for a more
finished look. I glued leaves and ferns together and used a bull nose clip to
secure them while they dried. Then I glued the pieces to leaves in the floral
spray—just in case I want to change the sprays at a later date. The final touch
was a pine cone that I removed from extra spray. I always buy extra sprays (at
the dollar store if possible) so I have more material for fill-in.
Ta da! It's finished and ready to hang. If necessary, you can bend portions of the floral sprays for the look you want.
Lesson Learned
Now that the skate is hanging on the door, it "lists" to the right, and to me it looks a little off balance with the heavier spay to the right. It would be in better balance if I had located the large spray to the left in the finished skate. So, crafter beware. Work to keep your floral sprays positioned in the skate, with good balance to offset the toe down position of the skate when it's hanging. The one I made for a gift (shown below) does a better job of that.
Great for A Gift
Now you can make another one with the remaining skate to
give a friend. For a less traditional look, try brightly colored whimsical
"floral" stems, like the glitzy ones I found on sale. I gave my dear
friend, Sheryl, the option to choose either skate as her Christmas gift—early—so
she could use it. I made the glitzy one for her and that's exactly what she
chose. When I told her that it was the one I made for her, she said, "You
nailed it!" I loved it too and would have been fine with the glitzy one if
she had chosen the one I made for me.
Notice that I made a glitzy bow to fill
in at the lower edge of the arrangement and glued it in place on the floral stems at the upper edge of the skate. I used wire-edged ribbon so I could shape the bow and tail pieces on the finished skate.
Hope you enjoyed this project tutorial.
Until next time,
Keep on sewing, quilting, and crafting!
And Happy Holidays!
Barbara
and then my horror to find a cut in the lower back. The sweater was too pretty to leave behind so I bought it anyway. Then, what to do with it?
I thought I could fuse a piece of interfacing under the slit and wear it anyway—but the sweater proved a bit too small so into a box it went.
Step 6: Salvage a piece of the sweater from the cutaway to "mend" the hole with fusible web. Apply the web to each side of the slit on the wrong side with the iron and them remove the protective paper to expose the web.
Step 9. With right sides facing, stitch the upper raw edges together where you cut the "pillow" section away from the upper part of the sweater. Stitch again, close to the first stitching. Trim excess, leaving a 1/4"-wide seam allowance. Turn right side out and steam press as needed. 
